• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

In order to avoid errors when many devices are connected, cables of the same colour should be used for all the connections to the terminals A and cables of the same colour should be used for all the connections to the terminals B of the various devices (e.g. white for A and blue for B). The solution is provided by the Laureate DIN rail mounted breakout board, which provides two RJ11 jacks with six screw clamp terminals all wired in parallel. Not more than one breakout board is required per RS485 line. If multiple analog input meters or transmitters are digitally addressed in command mode on an RS485 line using the Modbus RTU protocol or the Custom ASCII protocol, the rate becomes about 2 readings per second. The recommended arrangement of the wires is as a connected series of point-to-point () nodes, a line or bus, Ideally, the two ends of the cable will have a termination resistor connected across the two wires.

The termination also includes pull up and pull down resistors to establish bias for each data wire for the case when the lines are not being driven by any device. Being a connector that is frequently used outdoors in severe environments, it is designed to be IP68-rated waterproof and dustproof. There is no standard connector for the protocol. This cable provides a USB type A connector for the PC end and an RJ11 connector for the meter end. When a single RS485 meter or counter is connected to a PC via a cable CBL06, set the PC to 9600 baud. Confirm serial port parameters such as baud rate, data bits, and stop bits: Baud rate should be configured according to the connected RS485 device, commonly used rates are 9600 and 115200; Refer to the device manual or contact RS485 device technical support for configuration, especially if set to Modbus mode, confirm if the function code matches. Then use front panel programming to set the baud rate, protocol, digital address, half or full duplex, and other available parameters. Setup is the same when multiple meters are interconnected via cables CBL03, except that all meters now need to be set to a different digital address via their front panel.

So in order to transfer data from a RS232 serial interface engineers need a converter to be able to connect to a RS485 or RS422 interface. There are different serial communication standards such as RS232, what is rs485 cable RS422 and RS485. Confirm hardware connections including serial port devices, and check if your gateway and energy meter are correctly connected. See page 7 of the Laurel digital panel meter manual, page 7 of the Laurel counter manual, page 8 of the Laurel scale meter manual, or page 8 of the Custom ASCII protocol manual. Laureate meter and LT series transmitters support the Modbus RTU protocol and Laurel’s simpler ASCII character based Custom ASCII protocol. A meter will a thermocouple input and set for Modbus RTU needs to set to full duplex even if the wiring and the receiving unit are for half duplex. Set the PC to N81 for the Custom ASCII protocol, or to N82 or E81 for the Modbus RTU protocol. A single analog input meter or transmitter can stream readings to a PC at up to 60 readings per second and the Custom ASCII protocol set to continuous (or streaming) model. Use a 485 to USB serial cable, connect it to the interface of the 485 device and the computer's USB port, assign a COM port on the computer, open serial debugging assistant software, set the serial port parameters consistently, input the corresponding COM port, and monitor the data from the 485 device.

A T- --B; Check if the instructions sent to 485 are correct; Are there proper responses from 485 after sending correct instructions? Select the firmware for whichever Gen (2 or 3) module you are updating. Select the firmware for the appropriate module -- Wherever you have downloaded it to. You can do different combinations, for example if you have different Gen modules on your stack. For the example, we will use 4 battery modules on the stack. Should I use half-duplex or full-duplex RS485? RJ11 jacks support half-duplex or full-duplex communications. Both boards support the Modbus protocol and Laurel’s Custom ASCII protocol, as well as half-duplex or full-duplex RS485 communications. If you need technical support or have any feedback/review, please click the Submit Now button to submit a ticket, Our support team will check and reply to you within 1 to 2 working days. By using two jacks, up to 31 L485 boards can be connected in parallel for daisy chaining using readily available CBL03 data cables with no need for a hub. Laureate RS485 boards are available in versions with dual RJ11 jacks (ordering option 2, board P/N L485) and with dual RJ485 jacks (ordering option 4, board P/N LMOD).