• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

The process of installing a cat flap may seem intimidating however it's actually quite easy to do with the right instructions. First, decide how high you want the flap to be (on average the belly height). Mark this point on the door and then use the template provided as a guide to drill.

If you have a kitten that is still a baby, gently prop the door slightly open and invite it to walk through. Reward the kitten every time it passes.

Take a measurement of the door

A cat flap is a wonderful method to let your pet leave and come in and out of your house as it likes. This can keep your cat in good health as it will ensure that it is getting enough exercise and will also allow it to return inside if it is trapped outside during bad weather. It can also cut down on the amount of time you'll have to let it in or cat flap fitting out and can keep your home safe by letting you know when it has gone out.

However, it is important that the flap for your cat is correctly fitted to prevent your pet from being able to escape through it or be pushed through by any other animals (e.g. dogs). It is essential to measure your pet's belly height and the entrance to your home in order to make sure that the flap is at the correct height. You can adjust the position of your flap if your cat is smaller or taller than average.

Then, use a spirit-level to mark the middle of the door. This is where you'll install the flap. Then, using the markings as an indication, cut out the form of the flap with the help of a Jigsaw. After you've cut the door, sand the edges of the door to smooth the surfaces. Then drill any fixing holes required.

The process of installing a cat flap is not as difficult as you may think, and it shouldn't take more than two hours for the entire process from beginning to completion. However, the process could be slightly more complicated if you need to fit it inside the frame of a uPVC or composite door as these doors come with various thicknesses which can affect how the holes are cut and what they are inserted into. This is the reason we recommend calling a professional to complete the task, especially if you have never worked with glass before.

Measure Your Cat

A cat flap can save you from hours of hearing your pet's cries for you to let it in or out. This is especially helpful when you're at work most of the day and your cat has to stay in the waiting room until you come home in all weathers.

It is essential to measure your cat's measurements first before you begin the installation. Although it might seem like a simple operation it is essential to make sure you measure correctly or your pet will find it very difficult to use.

First of all, make sure that your cat is calm and not feeling anxious prior to taking the measurements. You'll need to hold them in a position where they cannot move and ensure that the measuring tape or ruler is flat against their body, not arching in any places. Keeping the ruler or measuring tape against their body from the top of their head to the base of their tail can allow you to get an accurate measurement.

Once you've got your cat's measurement and measurements, you need to look at the door to decide where to place the flap. The best option is to position the flap in the middle of your cat's belly because it will allow them to pass through it without too much effort. This will also avoid the flap making a lot of noise as it opens and closes.

You must think about the thickness of the uPVC or composite door too. While timber doors are of a similar thickness, uPVC and composite doors can be very different in their overall structure and this can make the installation of a cat flap more difficult because you must make sure the hole you cut is the correct size for your pet.

You can also use the template included in the instructions to mark the location of the hole in the door. This will help you determine where the opening needs to be and make sure the template is properly placed on the door. Using a spirit-level to ensure that the template is right against the door can be extremely helpful.

Cut the Flap

Before you can put in your cat flap you have to cut the door's panel to make it large enough to accommodate it. This is a difficult task and it is recommended that you get help from a professional cat flap fitting service to complete this task in case you don't have the knowledge or skills to do it yourself. It is also recommended to consult the instructions that come with the kit to learn how much to install a cat flap to do this correctly.

You can consider the height of the cat's or kitten's stomach to guide you. A good rule of thumb is to set the flap of your cat about 10 centimeters off the ground, as this is approximately the average height of the cat's belly. This way your cat will be able to move through the flap with ease and also give any other cats or curious neighbours a tough time trying to leave or enter.

The position of the cat flap on the door with a pencil. Next, if your kit comes with an outline of paper, place it over the door and use the markings to drill holes in each corner of the template. Then, you should be able to cut out the design of the template and cat flap fitting replace it with your cat flap fitting near me flap.

If you are installing your cat flap on a door made from wood or uPVC, you are able to do this yourself if you are comfortable with a Jigsaw. Be careful not to cut through the vertical rails or mullions of your door. You can use a jigsaw cut the panel into a square or a circle depending on the design of your cat flap. Be patient and don't try to force the jigsaw into cutting faster.

Once the hole is made then carefully insert the flap onto its new location and make sure that it is securely secured. If the flap has screw caps then push them into the protruding bolts. Once the screws are in place, you can sand any rough edges of the cut then apply sealant around any gaps to ensure there are no draughts coming into your home.

Place the Flap

If you have a basic cat flap you can open it and encourage your pet to use it by putting a little bit of cat food in front of the door. Alternately, you can push the cat through using your hands or with a stick. Once your cat is used to walking through the flap it will be capable of walking through the flap whenever it wants. This lets you let it in and out whenever it wishes.

It is possible to fit the flap inside a UPVC door or a glass door, however it might not be as easy as installing one inside a wooden exterior door. This is due to the fact that UPVC doors and some types of glass doors do not have an even thickness. This could have an enormous impact on the way you cut out the flap's hole and how well the flap fits after installation.

Depending on the type of cat flap you choose, it may include a mounting kit and a template that will tell precisely where to drill holes for it. If the kit doesn't come with a template you can use a photocopier to create your own. When cutting, it is important to keep the jigsaw from being pushed too hard so that you don't make a larger hole than necessary in your door.

The majority of cat flaps are rectangular or square in shape, but there are also some which are circular, and are usually more difficult to install. If you have a circular flap, ensure that the hole is in the correct place on the door. In the event that it is not, the cat might not be able to use it, and may be stuck outside the whole day (or at night).

Certain models of cat flap fitting near me flaps have locks which permit you to manage the time your cat comes and goes. These are useful if your pet is afraid of going out in the dark or coming back inside at night. They can also be useful when you are working all day. The lock can be used to allow entry or exit, and some can be locked in either direction allowing you to shut the door completely, which is especially helpful for cats with a chronic illness or older age who aren't willing to go out in rainy weather.