• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace a lock on a upvc door to Replace Door Locks

Door locks are your first security measure against unauthorized entry into your home. Signs of wear and tear as well as instances like moving into a new residence or burglaries, could trigger the need to replace your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will help you buy the lock that is right for you.

Deadbolt

If you want to ensure your door is safe from burglars, it's a good idea to install deadbolts. When the bolt is extended into the strike plate of the doorframe it makes it much more difficult for an intruder through the door. A single-cylinder deadbolt is activated by a key located on the outside and the thumb-turn mechanism situated inside. Deadbolts can only function when it is properly installed.

You will first need to determine if the door has a hole that is suitable for a deadbolt, or if you'll need to drill it out. Using the template that comes with the lock installation kit, mark the location of the hole for the deadbolt on the door's surface. Then, use your tape measure to determine the height the deadbolt should be. Then, mark the high point on the outside of the replacement upvc door lock. Use the speed square to draw a straight line across the mark you made for the bolt hole.

Then using a power drill, bore out the hole until it is on the opposite side of the door. This could take a bit of time. Then, sand the hole and the edge of the door until it is smooth. At this point, it's a good idea to paint or stain your door.

When the door is in place, replacing Lock in upvc door remove any screws visible on the existing deadbolt. This will reveal both the front and rear assembly of the deadbolt and its bolt inside. Then, unscrew the bolt and replace it with a brand new one that matches the door hardware. You will need to unscrew the bolt from the setplate. After this is done, you will need to chisel out the area for the strike plate that is on the door frame.

If your strike plate is misaligned, it's likely because the previous installer didn't mortise it correctly or a weatherstripping popped up and altered the strike position. To correct this issue it is necessary to remortise both the strike plate as well as the deadbolt. Close and lock the deadbolt after you've completed this step. Be sure the bolt extends into the strike plate, and then test the key to make sure it opens and closes smoothly.

Knob

If a door knob wears out, it can make your home or business less secure. It can make it difficult to open or close the door, which is why it's an ideal idea to replace it. Replacing the knob is an easy DIY project and shouldn't take less than 30 minutes to complete. You can use a screwdriver as well as pliers to take off the old knob or handle Be careful not to harm any other parts on the door.

Spray WD-40, or another dry lubricant, onto the mechanism of your door knob prior to you begin. This will let the lock to move smoothly as you turn it. To ensure proper operation it is important to select a knob and handle that are compatible with your doors. If you don't have a doorknob that is compatible, you will need to purchase a replacement lock for upvc door.

Before you begin replacing Lock in upvc Door the knob, look over the knob you replaced to determine which screws are keeping it in place. If there aren't any screws, you can use a screwdriver to wedge between the cover plate and the plate with hidden screws and then remove it.

After you've removed your knob that was previously used, look it over for any signs of rust or damage. You'll need to clean it off if there are any marks or dents, but you shouldn't have to do anything major If the knob is in good shape.

Now is the time to put in the new knob. Begin by examining the knobs you've chosen to make sure that you're picking out the right one for your door. You'll need to pick one with an extending rod that locks with the rod mechanism of the second knob. After you've placed the new knob in the hole, slide it into the latch.

Thread the latch plate screws downwards, then test the spring by pushing down several times. The latch should pop up every time. Install the second knob and secure it to the rod mechanism of the first knob. Thread in the other long screws from the knob's interior through the hole in the cylinder of the doorknob on the outside and lock it in place.

Latch

A latch is a steel piece that extends out into the doorjamb to secure it shut. The latch is operated either by a knob or handle on the inside of the door, or by a thumb-turn on the exterior. The latch can be secured with deadbolts to prevent thieves from breaking through the glass. It also helps protect against intentional or accidental closing by animals or children. The latch can be fitted with a single cylinder deadbolt or double cylinder deadbolts, depending on the security level you prefer.

Installing a deadbolt can be the same as installing a latch but there are some differences. First, measure the setback of the doorjamb with a tape measure to make sure that the new lock will fit. The setback is the distance from the edge of the doorjamb, to the center of the hole to accommodate the faceplate of the latch. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If your setback is greater than that, you might need to purchase an extra-long latch from a hardware or Replacing Lock In Upvc Door locksmith store.

Then, you'll need to make a hole for a latch plate into the doorjamb's edge. Use a chisel and chisel the latch mortise. Make sure that the depth is enough for the faceplate to be flush with the doorjamb. Tape the strikeplate to the doorjamb to ensure it is positioned properly.

If the strike is too high, you could knock the door down or apply pressure using the tire iron or crowbar. This could also cause cracks in the doorjamb. To remedy this, the strike can be lowered by drilling a new hole through the doorjamb, and then chiseling out the center of the old hole.

The final step is to put in the new strike plate which can be done by screwing it over the screw holes that are already in place. Utilize wood putty to fill in any old screw holes or bolt holes that aren't being used. After the putty has dried then sand it to a smooth finish.

Strike

The piece of metal that connects the deadbolt and latch when the door is shut is an electric strike. It is a crucial component of the overall security of a lock because it helps keep the door shut and offers additional resistance to kicking or force applied to the door. If a door is equipped with an electric strike, it can only be opened by keys or the control unit that governs its electrical impulses.

In the past, installing an electronic strike was as simple as cutting a piece of a doorjamb to release the latchbolt of a cylindrical lock from the pocket inside the strike. This modification is not only ugly and unattractive, but also exposes the mechanism of the latchbolt and the keeper to intruders.

Recently, several electric strike makers have come up with a brand new electric strike, dubbed the "No Cut" strike that doesn't need cutouts in the doorjamb for operation. These strikes have a unique design that allows the keeper and latchbolt to slide into the strike pocket without damaging the doorjamb faceplate.

The strike has an internal ramp which lifts the latchbolt as well as the keeper when it receives a signal from the reader. The retracting of the keeper and latchbolt causes them to rise on the ramp, thereby locking the door. When the upvc door locks replacement is closed, the deadbolt remains in place and the latchbolt is retracted into the keeper.

Installing an electronic strike is a straightforward process, particularly when you're replacing an older strike. If you are upgrading an existing access control system to an electric strike, you must ensure that your new system is compatible. You will also have to ensure that the strike is properly connected to your access control system and set up to operate in a safe manner.

Upgrade your strike plates to high duty strike plates to stop unauthorized entry. The plates utilize four to six three-inch screws instead of the two, three-fourth inch screws commonly employed in regular strikes. The longer screws make it more difficult for someone to break the frame and then reach inside to turn the piece that turns the thumb of a single deadbolt cylinder.