• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About boarding up doorway Up a Door

Boarding up a door is one method to shield vacant investment properties from the elements. It's not guaranteed to stop all damage, but it can help to avoid some of the issues that are associated with severe storms.

Boarding up windows and doors can also deter burglars or vandals from entering your property. Installing plywood panels over openings can be costly and time-consuming.

Measure the Door

The first thing you'll require is an accurate tape measure. It is a good idea to keep a chair or ladder close by in case you require to see more clearly the top of the frame. If you need to use these tools, make sure to wear gloves and safety glasses.

Start by measuring the length of the door. This can be accomplished by running the tape measure horizontally across the door. Make sure to remove any extra door parts, such as the door sweep to get this measurement. Then, you can determine the height measurement by measuring up from the floor to the current sill plate or lintel. It is crucial to measure multiple locations, especially with older doors, since they are not always an exact rectangle. If the measurements vary take the largest number.

After you've recorded the width and height measurements and you'll need to figure out what size boarding up a door you'll need to fit into the frame. Ideally, it should be 2'' larger than the door and 1 inch thicker than the door. 2'' higher. This will give you plenty of room to move the frame and door into place.

It's a great idea to remove the trim or casing around the jambs of the door to be able to see the studs. This will allow you to determine the exact size of the space between the studs and the edges of the frame.

After removing the trim, measure the width of your door frame using a tape measure. Take measurements of the frame at three different points and use the smallest measurement. You should also take measurements of the frame's height from top to bottom on both sides. Choose the shortest measurement to determine your door's width.

If you are having trouble with the measurements, you should seek out a professional who will come to your home and do the measuring. They'll tell you the dimensions and what kind of door Boarding up you'll need and how to prepare your frame for a new door.

Cut the Plywood

A door frame is usually composed of thin boards or studs that create an open space around the door. The typical door is held in place by two hinges fixed to the studs. This means that if you need to restore the door, it's necessary to remove the hinges from the door over the course of a few days. Placing plywood in the door opening is a simple method to board doors and stop insects from getting into your home. It's easy to do this without the need to nail or screw the plywood to the frame of the door.

Plywood is easy to work with, cheap and looks great once it's finished. This makes it the perfect material for temporary solutions to an issue that requires the removal of an existing door and refinishing or installing a new one. It can also be used to secure the opening of a space being renovated, like the construction site or basement.

Begin by measuring the width of the door opening as well as its height. Note the measurements using a utility blade and a straight edge made of metal, such as the drywall or metal square. Next, snap the chalk lines across all the lines marked to mark the areas you want to cut. Finally utilize circular saws to cut out the plywood to the desired size.

It is crucial to protect your ears and eyes when cutting plywood. If you can, wear a pair of eye protection and earplugs as you are working. In addition, it is important to use a blade with a lot of teeth that can cut quickly and without tear-out. Make use of a small piece wood to guide the blade. Keep it a hair's distance from the marked line when cutting.

A great way to hold the plywood in place without screwing it to the studs is by fixing two braces at each end. Put one of the braces on the inside of the door and the one on the outside. Position a pair 1-1/2-inch deck screws in each hole and tighten by using an open-end ratchet.

Fasten the Plywood

When you have a piece of plywood cut to the right dimensions and with the holes for the door frame's rails and stiles already drilled, it is time to attach the panel to the door frame. This is a relatively easy project that doesn't require extensive carpentry skills, provided you follow the right procedures and use the right tools.

Set up a table in the doorway, with two sawhorses at each end and framing lumber 2x4s. Use the marks made during the measurement procedure to guide you in cutting the plywood. Mark the lines using an utility knife and a drywall square or any other metal straight edge. This will provide a guide for the saw blade and prevent splintering when you cut the plywood.

Wear eye protection and use a circular table saw with a fine-toothed blade to cut along the line of scoring. Sand the edges of the panels with 120-grit paper to smooth it out and eliminate any burrs. After the sanding process, apply a coat of wood sealer on the plywood panels and let dry as directed by the manufacturer.

Install the hinges onto the frame of your door. If you're using a T-hinge drill holes on the outside edge of your door to allow for the straps of the hinges. Then, place the outside hinge on its spot and attach it to the frame with a screw gun. Repeat the same procedure on the inside of the door for each of the hinges remaining, but be careful not to overtighten any of them, or the panel may shift.

If you have an outside hinged door with only one T you can make it easier to close and lock using a chain latch by fishing a piece of wire through the loops on the outside hinges. Fold a short piece to make a half-way tie, and then put it through the two holes on the outside of the door. Then, you can twist the wires together and secure the door.

Install the Plywood

Using the measurements you took using the measurements you took, put the plywood in the door opening. Shim the header of the frame (top) and the sill. Use a level to make sure that there is no slop between the header and sill. If it isn't perfect then place another shim if necessary and continue the process until the sill and the header are plumb.

Once the plywood is set, secure it with the stainless-steel hinge bolts and wingscrews. It's a good idea to use a screw gun with an attachment for a hex-head to prevent stripping the head of the screws.

If your house has studs running along your doorway, it is possible to drill hanger bolts into every framing piece. This is much easier than using a drywall cutting tool to make the hole.

After installing the plywood take measurements of the width and the height of the door opening. If necessary, trim the bottom of the plywood to fit the size of the door frame. Cut two pieces of 1-by-6 framing lumber for braces to attach across the upper and lower sides of your door. Wear eye protection and cut along the lines that are marked on the plywood using a circular saw equipped with a fine-tooth blade. Remove any splinters from the cuts with an the sanding block.

After you have placed the braces, use two pairs of finishing nails of 2 inches to secure each brace to the plywood. When you're finished, counter sink the heads of all nails. Seal the braces and the plywood with a high-quality wood sealer, like this wipe on polyurethane from Minwax.

If the door is too big, you can either add decorative molding to fill the gap between your door and jamb, or you can alter the size of your opening. In many instances, however it's cheaper and simpler to purchase an entirely new door. This also eliminates any headaches you may have experienced with the original door if it was damaged and didn't longer fit the opening.