• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat abarth key 500 Key Fob Won't Work

A fiat 500 key fob is a great way where to get a fiat key cut unlock the doors and start the car. However, there are a variety of reasons why the fob won't be functioning. These include a dead battery damaged receiver module, water damage issues, or interference.

This listing is for a NEW replacement fiat 500 electric key (https://Olderworkers.com.au/) Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to search for local automotive locksmiths). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob will not work is a dead battery. Modern key fobs only have only a limited range of operation and must be within a few inches of your vehicle to work. If you are not within your vehicle, and you press the keyfob button, it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the coin-cell battery (Part Number CR2032) by a new one of a reputable brand such as Panasonic Duracell or Energizer. They are usually available at your local hardware store or online.

You can test the coin-cell battery by pressing the buttons while you are standing close to your Fiat 500. The parking lights will flash and the key fob should operate the lock and unlock switches.

If the key fob doesn't work after replacing the battery, it may have water damage that prevents it from connecting to the receiver module inside your vehicle. Water damage can occur in a number of ways, from small splashes to submerging your fob in salt water at the beach. If you suspect that your fob has been exposed to water, you can try placing it in a dry rice bag to draw the moisture out. If that doesn't work, the fob might need to be reset by an experienced auto locksmith or by the dealer.

Water Damage

While the fob has some rubber seals to keep water from the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short, and eventually fail. It's not good to get the fob wet however, but don't give it up if you accidentally drop it in water or fail to remove it from your pocket.

First take the battery off the fob. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Then, test the fob to check if it functions. If the key does not function it could need to be reset. This is usually handled by an auto locksmith or dealer.

If the key is older and hasn't been programmed to your car, it will likely need to be replaced completely. A professional locksmith for cars can do this job. The locksmith will need the key to be cut to match your car's ignition. They'll also need to reprogram the fob to the system of your car. This is a quick and affordable process that can usually be completed on the next day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob might stop working is because it's out of range. The remote has a maximum range of 30 feet. Therefore, when you're too far from your vehicle it won't respond to your commands. This can easily be resolved by moving closer to your vehicle until it begins responding.

If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and fiat 500 electric key your fob doesn't function It could be because of an internal circuit board issue. In the majority of cases, reprogramming your fob will solve the issue. You can find instructions on how to do this on the majority of vehicles by searching YouTube or looking through the owner's manual.

You may need to replace the metal clips that keep the coin battery. If they loose tension they could stop the coin battery from being properly seated and could cause your remote to malfunction.

In rare cases the fob might be out of the vehicle's sync because of hardware or software problems. This could be a huge problem, but you can frequently fix this issue by visiting an auto locksmith to have them reprogram your fob for Fiat 500 Electric Key you. In some instances, the software may also require reinstallation into your body control modules.

Interference

Interference can also cause the key fob to be unable to receive or transmit an signal. This is possible when the key fob is located near the radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. The key fob could not work due to a poor connection to the buttons, water damage or damage to the internal chips.

If the key fob failed to work one day without notice or after trying everything you can at home to fix it e.g. replacing the battery, reprogramming it and using the spare key fob, you might have a faulty receiver module on your 500. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's internal system, including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electrical charge, and then restart the computer in your car. This could help you get your key fob working again. If the issue persists, you should consult a certified technician. They will be able to diagnose the exact cause of your issue.