• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a door hinge that is loose can be a doable job for most homeowners. If, however, the holes for screws are smashed and won't hold screws you might have to add dowels and wood glue before you can reinstall the hinge.

Before you do that though scrub away any surface corrosion. This will aid in keeping the dowels in place and provide an adequate base for them to rest on.

Take the Hinges off

Many hinges for doors can be removed, making it simpler to move a door from one side of the frame to the other side or take the entire door off in the event of need. Anyone with a little patience can take the replacement hinges off, but you must be aware of what to do.

If the hinges have been painted, you'll need to remove it before you attempt to remove the pins. If you do not, the paint may be smashed off and scratch your door when you attempt to lift it. Put the hinges in an stainless steel pot and fill it up with water to the point that the hinges are completely submerged. Allow the hinges to sit in the pan for approximately 30 minutes. The heat from the water will soften the paint and make it easier to take off the pins.

After the pins have been loosen, you can remove the hinges from the door and frame. You can employ a screwdriver for the job done, but it is recommended that you make use of a magnetic screwdriver for this project. This type of screwdriver has been specifically designed to grab screws made of metal and will assist you in getting the task completed much quicker.

It is a good idea to spray lubricant on the hinges prior to attempting to remove them. A simple lubricant can help the process move along quickly and help you remove the pins and screws. You can purchase this kind of lubricant in most hardware and home improvement stores.

You should also keep in mind that the number of door hinges you will need will differ based on the kind of door and the configurations. Heavy doors and solid-core doors will require more hinges while lighter-weight and hollow-core doors might only require two or three.

It is also crucial to know the various types of hinges to determine which ones will best suit your needs. Exterior hinges are generally designed to support the door's weight, while interior hinges will need to be able to handle heavier loads.

Reattaching the Hinges

Sometimes a door hinge will get looser and eventually begin to hang out of alignment or slide. This can cause problems, but it's usually easy to Fix door Hinge. Most of the time, a simple retightening of the screw will resolve the problem. However when the screw holes are ripped out, this can be more difficult to accomplish. Fortunately, there is a trick to get these holes back to their original size that utilizes a wood dowel.

Start by drilling the old hole using a drill bit close to the new screw size (normally 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a snug fit, the dowel must be cut at the same length as the screw. Reinstall the screw, and tighten to desired degree of tightness. If the door continues to have the tendency to be bowed and close, then you can add another dowel to the gap and repeat the procedure. Close the door slowly after each adjustment to ensure that the perimeter clearances are in order.

You could also use a wood plug in place of the dowel. It will work just as well but might take a little longer to set up. You can use a piece of wood that has been whittled to the proper size. If you don't have a woodworking tool, you can also use toothpicks or wooden matches as well.

Make use of a countersink in order to make the hole smaller for the head of the screw after you have installed it. This will stop the screw from hitting the edges of the doors when they are opened and closed. This will make it much easier to tighten the screws when reinstalling hinges.

Once you have reinstalled the hinge, be sure to coat it using a dry lubricant to help keep it from getting stuck in the future. You can use products such as PB Blaster and Liquid Wrench. You should apply a light coat and wait for around 15 minutes to fully penetrate the barrel of the hinge.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door, you can make a few minor repairs. Make sure the screws that attach the hinge plate in place to the door frame and frame are in good condition. If they're loose, tighten them with an electric drill or screwdriver. Be cautious not to over tighten the screws, as this could cause gaps to form at the trim joints, or more seriously, tear out the threads.

If the issue is that the hinge plates are separating, you can reattach the plates by applying wood glue on the back of them and then inserting wooden dowels or toothpicks in the holes. The dowels or toothpicks provide a solid base for the screws and keep the plates from moving when you drive them into place. Allow the glue to dry before attaching the hinge.

The screws may also be damaged or missing. It is possible to fix this issue by replacing the screws with longer ones. Use a drill that is the same size as the screw hole to avoid drilling into the jamb or hinge.

Close the door after you've reattached your hinge and measure the gap between the frame and the door. It should be approximately the thickness of a nickel all around or less if there's a gap that was caused by a previous door that was not properly hang. If the hinges were installed correctly, this shouldn't be a problem.

If the hinges still seem loose, try adding a stronger hinge between the hinge plate's surface and the mounting surface. This will allow the hinges more space. You could also try removing the hinge pin from the problem hinge and pounding it down using a hammer to make it more secure or using an entirely new hinge pin. You can also lubricate your replacement hinges with mineral oil or jojoba to decrease friction hinges for timber windows and hold them in their place. Lubricating your repair window hinges regularly will help prevent them from becoming stiff and squeaky, and also extend their lifespan.

Cleaning the Hinges

The constant movement of a hinge creates friction, which attracts dust particles. Without regular cleaning and lubrication, the particles become stuck in the moving parts of a door hinge and build up over time. The hinge will get stiff and creaky, and its appearance may rapidly deteriorate. Regular cleaning, lubrication, and inspections will maintain the integrity and functionality of hinges that are attached to doors.

Check the hinges to see how much rust has accumulated on their surfaces. If the corrosion has reached the point of destroying surface of the barrel or screw holes, you'll have to replace the hinges. If you are able to save the hinges, you can remove any loose rust by using steel wool and wire brush. Apply a commercial rust-removing product or homemade solutions like lemon juice on the hinge. Allow the rust remover to be on the hinge for a few minutes to penetrate and dissolve any remaining rust.

Retightening screws can help restore hinge function if you don't want to spend time or money on repairing hinges. It is possible to attach dowel or shim made of wood to the hinge when the screws have been shaved. Wooden dowels come in round rods that vary in sizes and lengths. You can buy them on the internet, at woodworking supply stores and at home improvement stores.

You can also create an shim using either plastic or metal, depending on the type of hinge you own. To make a dowel cut a piece made of wooden dowel or another sturdy material to the size you want. Then, dip a dowel into carpenter's adhesive and then insert it into the hole. The glue will secure the dowel in the position.

Before cleaning the hinges, put down a paper towel or cloth to protect your flooring from spills. Once the area is protected then clean the hinges using a soft cloth or sponge dipped in a mild cleaner or vinegar to get rid of built-up dirt, grime and tarnish. A toothbrush or small brush can be used to access hard-to-reach areas in crevices and difficult places.