• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat key duplication 500 Key Fob Won't Work

A fiat car keys 500 key fob allows you to easily open doors and start your vehicle. There are many reasons the fob could stop working. This includes a dead coin-battery, water damage, issues with the receiver module, and interference.

This listing is for an NEW replacement fiat key fob not working Flip Key Remote - like the Ilco brand that must be programmed professionally by a local locksmith (click here for Locksmith Search). Includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not functioning. Modern key fobs offer an operating range that is limited and must be within only a few inches from the vehicle in order to work. If you're far from your vehicle, and you push the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a new one from a reputable brand such as Panasonic Duracell or Energizer. You can typically find them in your local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you're standing close to your fiat key replacement near me 500. The car will blink its parking lights and the key fob should work the lock and unlock switches.

If the fob's key doesn't work after replacing the battery, it could be damaged by water that blocks it from communicating with the receiver module inside your vehicle. Water damage can happen in a number of ways, from the slightest splash to submerging the fob salt water at the beach. If you suspect that your fob has been exposed to water, you can try placing it in a dry rice bag to draw the moisture out. If this does not work, you'll need to have the fob reprogrammed either by an auto locksmith or a dealer.

Water Damage

The fob does have rubber seals to keep water from the electronic chip inside the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to become shorted and eventually cease to function. If you get the fob wet, it's not an ideal idea however, if you drop it in the water in a cup or forget to remove it from your pants pocket before running the washer do not give up hope.

First remove the battery from the fob. Clean the electronic chip using isopropyl alcohol or another similar product and dry it thoroughly before replacing the battery. Next, test the fob to test if it works. If the key does not function, it may have to be reset. This is usually handled by a professional or dealer auto locksmith.

If the key is older and was not programmed to your car It will most likely need to be replaced completely. This is a straightforward process that can be carried out by a professional locksmith for automotive use. The locksmith will require the key cover fiat 500 cut to match the car's ignition. They'll also have to program the fob into your car's system. This is a fast and inexpensive process that can be completed within the same day.

Receiver Module Issues

Your fiat 500 keys key fob may stop working because it is out of range. The remote has a range of 30 feet, which means should you be too far from your car it will not respond to your commands. You can remedy this by moving your remote closer to your vehicle until it responds.

If your fob doesn't work after you replace the battery in the coin, also called a "button", "watch" or "button", it could be a problem with the internal circuit board. In most cases, reprogramming the fob will fix the issue. The instructions are available for the majority of vehicles on YouTube or in the owner's guide.

You may need to replace the metal clips that hold the coin battery in place. If they lose tension it can prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases the fob may be out of the vehicle's sync because due to hardware or software issues. This can cause a major problem, but you can usually fix it by visiting a local dealer or auto locksmith to reprogram your fob for you. In some instances they might need to reinstall the software in your body control module too.

Interference

Interference can also cause the key fob to not receive or transmit an signal. This is possible when the key fob is located near an electronic radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob could not function include a weak connection to the buttons or damage to the internal chip or water damage.

If the key fob failed to work one day without notice and you've tried everything you can do at home to solve it e.g. battery replacement, reprogramming and using the spare key fob, you could have a malfunctioning receiver module on your 500. The receiver module, which is located under the dashboard, is able to pick up radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then translated by the vehicle.

There is a straightforward method to reset the 500's internal system including the keyfob. Disconnect the battery 12 volt for approximately 15 minutes by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will erase any remaining electric current, and also restart the car's computer. This can help you get your key fob to work again. If the issue continues, you should speak with an expert technician. They can determine the exact cause of your issue.