• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix Car Ignition Problems

The car will not start unless the switch transmits an electrical signal to the starter. Over time wear and tear may cause the switch to fail.

You can remove the steering column trim with specialized tools to gain access to the ignition cylinder module. Check your repair manual for instructions on how to do this correctly.

1. Check the Switch

One of the most frequent ignition problems is a bad switch. It regulates the time when relays are activated and deactivated through the use of bridge. Because it isn't able to channel the full power of devices like the starter, it's a less powerful component that's less likely to fail. The switch could still be damaged or corrosion-prone.

One indication of a defective switch is a difficulty turning the key. This can be due to many factors that include not inserting the correct key correctly or the mechanism being worn out over time. It's also commonplace for people to misplace their car keys with someone else's, which can cause mechanical damage.

If the switch isn't working there are a few things you could try before calling a locksmith. First, you must ensure that the battery is fully charged and there aren't any electrical issues in the system. You should also examine the voltage of every component to see if they're providing enough power. Once you've completed these steps, you're ready to begin troubleshooting.

Fortunately, the ignition switch is simple to replace. It's connected to the ignition cylinder, which is a round module that holds everything together. You'll need a flathead and something that is long enough to press the pin in. You can employ anything from a paintbrush to Kabob stick, but be careful of anything that is brittle, as it can be broken into the hole.

When you're ready to do the job, you'll need to take off any trim pieces covering the area around the ignition switch. After that take off and loosen any screws that keep the switch in place, and then gently pull it out. Depending on the model, you may need to disconnect the cables that connect to it. If you have a manual for your vehicle and model, it will show you exactly how to do this.

If the ignition switch isn't functioning it is recommended to have it replaced by a professional. It's not easy to replace the ignition switch without disabling the steering column. This could lead to an accidental deployment of airbags if you do it incorrectly. It's best to leave it to your local locksmith to take care of this.

2. Check the Wiring

Your car may not start if you cannot turn the key or it isn't starting. This could be due a number of components within the ignition system. Understanding how the ignition system functions can help you spot problems and make the appropriate repairs.

The ignition switch is an electric switch that has multiple poles and is operated by the key. It has four positions including off, accessory, run and "lock." If the switch is locked (which is typically indicated by the red light), the ignition circuit is activated and it is not possible to start your car.

To determine if the ignition switch is damaged or if the ignition coil itself is faulty, you'll need to do a quick electrical test using a voltage meter. When the ignition switch has been set to run, the voltmeter should show around 12.6, If the voltage falls below that, it indicates there's an open circuit somewhere within the system. This could be at the solenoid, the battery or even the ignition coil itself.

Disconnect the electrical connector so that it does not interfere with the test. Set the voltmeter on the continuity or resistance modes and then place one lead on one of the terminals on the ignition switch. The other lead should be connected to the positive terminal of the battery. If the voltage meter shows "open" or does not register any voltage it's time to replace the switch.

When replacing the switch, make certain to use a new ignition cylinder as well as a high quality key cut to ensure that your vehicle will start and run correctly. When you replace the switch, ensure not to hit the pins of the ignition cylinder using your tools. Otherwise, they'll become stuck and the engine won't be able to run. You'll need to remove the steering wheel as well as the gear selector on some vehicles to access the ignition cylinder. This isn't easy, and it is not recommended until you have an owner's manual that states it's safe. If you don't, it is possible to cause irreparable damage to your steering column and shift mechanism.

3. Check the Cylinder

If you've tried the battery, the wiring, and the ignition switch, but still cannot start your car it could be time to examine the cylinder. It's the component that holds your key, and is mechanically connected to the lock on the steering wheel so that a potential thief cannot steer the car without keys.

You may be noticing that your key does not rotate if the cylinder is worn out. The pins of the cylinder can get stuck as they adjust to the shape of your key. This can cause your car to not start. The cylinder could also be loose and a tap using the tack hammer may assist in releasing it. Be sure not to mix the springs, and fix car ignition ensure that your key is correctly installed.

Another sign that your cylinder is going bad is when you have to turn the key and test it in various positions before it begins. This is a bad indication and should be addressed immediately, as it can only get worse over time.

To test the cylinder, you'll need to disconnect your battery and remove the cover around your steering wheel until you can access the ignition module. The old mobile ignition lock repair services switch should be easy to remove, as well as the cylinder for ignition made of metal. If you don't have an additional ignition switch around, it's likely possible that you can take your original ignition switch and the cylinder to a locksmith in order to reuse them as long as they are in good condition. After replacing the switch and cylinder, be sure to reconnect the wiring harness and secure it and reattach any covers or panels you've removed.

4. Make sure you check the Spark Plugs

The spark plug is your ignition system's final link. When it breaks, the engine can't run. This could take the form of your car ignition switch repair not starting at all, or it may start but run poorly. In either case, it's likely that one of several factors are hindering or blocking the flow of electricity across spark plug gaps, which ignites the fuel mixture and air inside your engine.

Before you begin working on your spark plugs, make sure that you work on a safe surface and using protective gloves and tools to prevent being zapped. Spark plugs are hot and could cause serious injury when touched with your skin.

When a spark plug is bad, you might notice that the tip of the central electrode is covered with a light gray or brown substance on it. The electrode could also be covered with a dark layer. The deposits or fouling may stop high-voltage electrical current from crossing the gap of your spark plug, igniting an engine.

If you suspect your spark plugs might be the cause You could test them by remove them from the tube that is inside the ignition coil. This can be done by disconnecting the coil and the plug wire. Then, you'll have to follow the proper procedure for your vehicle to remove the components that cover the plugs. Once you have removed the plugs you can place them on a grounded metal surface and then crank the engine. If they're functioning you will be able to see a strong blue spark on the tip of central electrode.

If you don't see a spark, you've identified the issue. Next, you'll need to go backwards through the chain of ignition and test each component until the spark plugs aren't functioning. Every system will wear out and eventually fail This is especially relevant to ignition systems. But, regular maintenance can help slow the process down and prevent a major problem at the worst moment.