• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your pet come and go as they please without having to let them in or out. They also can help to keep your cat from having to go to the bathroom inside the house.

It is simpler to install an animal flap on a upvc panel than one made of glass however, you'll require some expertise and appropriate tools.

Take a look at the Door

The installation of a fitting cat flap in upvc door panel flap inside a door can be tricky but as long as you use the correct type of cat flap, take your time and follow the directions provided, it should not prove to be too much trouble. We will show you how to draw the shape, using the jigsaw to slice the area in the door and then finish off the job by fixing the flap to the door. This will ensure the flap stays in position and also protects the doors from damage caused by wind and rain.

To determine the size of the cat flap you need, measure your pet's width. This will ensure that the flap is large enough to let your pet go inside and out of the house without having to open and close the door each time, but it is also small enough to prevent the pet from straying too far in either direction.

Once you have the measurements, you can determine where on the door the template should be placed, typically this is done using an X, however some kits come with a drawing that shows where to drill. If yours does, then you can stick it to the door and use a pencil to draw around it. If your door has a sill or moulding along the bottom edge ensure that you have enough clearance from these because this will keep your cat safe and prevent them gaining access to your home.

Next put on your eye protection as well as a dust mask. Then using a jigsaw begin cutting along the line that you have pencilled in. Don't push the blade too hard as this can cause it to cut faster than you would like it to. Use a set square to ensure that you are cutting the material in a proper manner and that the hole is a rectangle. When you are satisfied with the final result, you can take the door material off.

Draw a Line

The cat flap is a great method to let your pet in and out without having to worry about them coming in with visitors or leaving unwanted gifts inside the home. It also stops draughts and keeps your home's temperature stable. However, putting an animal flap on your door can seem like an overwhelming task for those who have never done it before, leading many people to seek out an expert joiner or carpenter to complete the task. This is an option but you can do it yourself, provided the tools are in order and the steps are adhered to.

While this is far simpler to accomplish with a timber door, it is still possible to do this in uPVC doors - although you need to be very cautious not to damage the doors since this could cause damage to your warranty. The first step in the process is to take measurements of the door, making sure that it will fit the new cat flap. This should be easy enough when you have the standard uPVC door, however you might need to take more care if using an alternative type of door as these can be more difficult to cut than solid upvc door panel with cat flap panels.

The next step is to determine the height of your belly for your cat. This is the measurement from the floor to the underside of the cat's stomach and you'll need to locate a place near the door where this measurement is within the range your pet can comfortably go through. Once you've got the information, you'll be required to mark the space with a spirit level and a pencil so that you are certain that the hole will be suitable for your cat.

Once you've marked the area, it's time to cut the hole. It is important to be patient and use a jigsaw ensure the cuts are clean and smooth, not rough and uneven. This could damage your door. It is also important to wear safety glasses and a dust-proof mask whenever working with the jigsaw as breathing in the dust could be hazardous to your health. After you've cut the hole, you will require sandpaper to smooth the edges so that the cat flap is easily inserted.

Cut a Hole

Installing a cat flap to an existing door panel or double glazing sealed unit can be difficult. It is tempting to do it yourself, but unless have a lot of expertise in DIY, it's likely to be best to have a professional to do the job for you. A mistake could not only be unsightly and unattractive, but could also be a security threat. It could allow cold air in when the cat is outside and hot air to escape when it is inside.

Mark the hole's position on the door using an eraser and a spirit level. This will ensure that it is correctly positioned and aligns with the rest of the door. Make sure you have some sandpaper to smooth any rough edges.

Wear any safety gear you need to work with an electric tool. If you are worried about the sound produced by a jigsaw you can buy a cordless version which is much quieter and easier to use.

You should only remove the material that is required to make the flap. It is essential to leave a bit of material to make the wall thickness of the flap. However, removing too much can cause problems or even damage the door frame.

If the upvc door is made of metal, or has a frame, it may interfere with the microchip flap. In this case you'll need create an extra-large hole to ensure that the metal doesn't touch the walls of the flap.

If you're looking to install a cat flap cover for winter flap into a upvc or double-glazed window with metal frames it is necessary to speak with a specialist. They will offer you a brand new piece of glass that has the hole already pre-made for the cat flap. It is much less expensive to have this done than trying to fix the cat flap onto an existing pane of glass that hasn't been designed specifically for the purpose.

Fit the Flap

Cat flaps allow your pet the freedom to move around anytime they want and let them relax at home whenever they'd like. If you've got a uPVC door, it may be difficult to put in an animal flap, especially in the absence of glass panes that could be cut to fit one. Luckily, if you're happy to purchase and install a replacement half-glazed uPVC panel, it's possible to install an animal flap onto the doors. It's not as simple as simply cutting a hole in the door however, and there are some things you'll need to do first to ensure it's secure.

A composite, uPVC, or GRP door panel is usually made up of a plastic skin which is bonded to an insulating polystyrene base. It is essential to be careful when cutting the material. This type door comes with a template that you can use to cut the hole.

Once you have marked the position of the hole in your door, now it's time to fit the cat flap. You can buy and fit a wide variety of different models that range from simple button operated ones to ones that are activated by microchips that allow access only to your pet. Whatever kind of cat flap you pick it is essential that your cat flap installation bristol is able to use the flap without getting stuck in bad weather.

It is a good idea to opt for circular fittings instead of one that is square, because circles are more securely cut into door glass. It's because square holes are more likely to break the glass when drilled. It's also a much safer option as you don't risk having to drill into toughened glass that might break and injure your pet or your family. This is particularly important if you have child or elderly person at home who could be hurt by shards of glass.